Clik here to view.
How to Create an IPSec Tunnel (Main Mode) Between Vigor3300V and ...
This guide will show you the configuration required to establish an IP Sec VPN tunnel (Main Mode) between a Vigor3300V and a Vigor3900 router. Vigor3900 Configuration Step 1: Go to VPN and Remote...
View ArticleClik here to view.
How to Perform a Factory Reset on Vigor3300V Router When Login Pa...
The 3300V router does not have a reset button to restore the router to factory defaults when the login password is not known. The following steps show how to restore the Vigor3300V to "factory...
View ArticleWhat is the Difference between the 3300V and the 3300V+
They have the following differences: Vigor3300V+ support ISDN,Vigor3300V don't support ISDN. The memory of Vigor3300V+ is 128M, the momery of Vigor3300V is 64M, The CPU of Vigor3300V+ and Vigor3300V...
View ArticleClik here to view.
How to Block all ports for 192.168.1.0 subnet 255.255.255.0 and a...
1.) 2.) 3.) 4.) 5.) 6.)
View ArticleVigor 3300 VPN Issue
3 VPNS connection to 3300 but 3rd connection fails with mismatch preshared key message. Remote VPN dialing into 3300 DrayTek solution We saw vigor3300 has 3 VPN which remote Gateway is 0.0.0.0. It's...
View ArticleClik here to view.
Port Redirection on Multi-Wan Router
Question: How do I set up the router to read the incoming website requests' target domain name, and route the user to the appropriate port on the co-located server? Answer When a external user accesses...
View ArticleClik here to view.
I need help with VPN on Vigor3300V
Click on the required link below for full details: 1. VPN Dial-in Function (PDF format) Describes setting up a LAN to LAN VPN tunnel between a Vigor3300V and a Vigor2900 router. The Vigor3300V has a...
View ArticleClik here to view.
How to Set up Second Subnet on Vigor3300V and use DHCP
Scenario Currently have network 192.168.16.0 configured on LAN port 1.Need to set up a second subnet 10.0.1.0 on LAN Port 2 with the 3300 as DHCP Server for both networks. Solution You may follow the...
View ArticleClik here to view.
How to Re-enable Access to the Vigor3300 Management Interface if ...
You can use the console port to re-enable access to the router. Connect your Computer serial port to the Vigor3300 console port.Console port settings: baud rate 57600, 8 bits, no parity,1 stop bitonce...
View ArticleClik here to view.
How Setup QoS for VoIP traffic on Vigor3300
Since VoIP devices use various RTP ports, it is recommended to set the QoS rule by IP. Assume the VoIP device behind Vigor3300 is with IP 192.168.33.100. Please follow the steps below to configure QoS...
View ArticleClik here to view.
How to Configure VOIP on Vigor3300V Router
Before you start to configure VOIP on your Vigor3300V router ensure that you have connected the Analogue Phones to the router and the router is connected to the Internet. Your chosen VoIP Provider will...
View ArticleDoes The Vigor3300 Support IPSEC VPN Pass Through?
The Vigor3300 supports VPN pass through. The VPN server will need to use ESP for IPSEC VPN security method. The NAT mechanism in the Vigor3300 supports NAT-T when ESP is used. The AH security method...
View ArticleClik here to view.
Scheduling Automatic Reboot of Vigor3300
Vigor3300 running firmware version 2.6.3 (EN) supports scheduled rebooting of the router. Telnet system command to use is “autoreboot” Command syntax is: DrayTek/system> autoreboot ? Full Name:...
View ArticleRestoring the Vigor3300 router to factory Default Settings When U...
The Vigor3300 router does not have a factory reset button on the front panel similar to the Vigor3300V router. Therefore we will need to use the console port to gain access to the router and perform...
View ArticleClik here to view.
How to Change LAN port Settings in Vigor3300 Router
This function is available from firmware version 2.6.2 and above and is only available in the Command Line Interface of the router. Telnet to the router and run the “switchport” command. This is...
View ArticleHigh Availability Mode in Vigor3300 Routers
This article describes how the high availability works with the vigor3300 routers:After enabling High Availability on both 3300 and setup the LAN IP and virtual IP addresses, the Slave unit will...
View ArticleClik here to view.
Configuring QoS for VoIP device behind Vigor3300 Router
For source and destination IP to specify ANY use 0.0.0.0Under service type specify none to indicate ANYDiffServ Codepoint leave it at "none" unless the server supports this. Assume we want 60%...
View ArticleClik here to view.
Configuring PPTP VPN Remote Dial-in Connection to Vigor3300
Vigor3300 Configuration Step1: Go To “VPN>>PPTP&L2TP>>General Setup>>PPTP General Setup” page. Enable profile and select Authentication method and Encryption Step2: Go to...
View ArticleHow can I configure Vigor3300V's FXO ports as Trunk lines for an ...
OK, so what you're trying to achieve is:(a) An incoming PSTN call is converted by the 3300V to a VoIP data stream and sent via Ethernet to the Asterisk server where it is handled as an incoming...
View ArticleWhere can I find information on how to configure VOIP settings on...
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the VOIP settings documentation here:...
View ArticleCan I use the Vigor3300V's FXS and FXO ports as a PBX?
Not directly, because the Vigor 3300 does not provide all the functions of a modern PBX. However see this Draytek Vigor 3300V Application Note on using Vigor 3300V with Asterisk Open-source PBX.
View ArticleInternet connection using PPPoA (in New Zealand)
We are aware that TelecomNZ doesn't support PPPoE (which is common in Australia), and that NZ customers must use PPPoA. This requires that the modem is configured to do the PPPoA login. It is...
View ArticleHow do I upgrade the firmware on my Vigor3300/V?
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the Firmware Upgrade Notes (Chapter 17) here:...
View ArticleWhere can I find information on how to configure VPN settings on ...
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the VPN settings documentation here:...
View ArticleWhere can I find information on how to configure WAN settings on ...
The Draytek Manufacturer has a comprehensive set of Application Notes regarding the 3300/3300V on their website. Please refer to the WAN settings documentation here:...
View ArticleOn Vigor3300 VPN, where/how do we set the remote and local IPSec ...
The "Local ID" field is used for IPSec Aggressive mode which is not supported on 3300 series; so the Vigor 3300V don't have "Local ID" field. There are two cases. Aggressive mode is used in IPSec IKE...
View ArticleVigor3300 DMZ port
There is a socket on the Vigor 3300's front panel labelled "DMZ". This is actually the "WAN1 port" (see here for details). The current Vigor 3300 firmware can use any of the 3 WAN ports for DMZ.Â...
View ArticleVigor3300 WAN and DMZ ports
The Vigor 3300 (not 3300V) model have the DMZ and WAN ports mis-labelled. The front of the unit shows a block of 4 LAN ports (P1-P4) and a block of 4 WAN ports, labelled "DMZ", "WAN1", "WAN2" and...
View ArticleClik here to view.
How can I get the Console Log from a Vigor 3300?
Connect a computer's serial port to the Vigor 3300 Console port using the supplied cable. this). On the computer, run a terminal emulator, such as the Windows Hyperterminal. Configure the serial...
View ArticleI need help with VPN on Vigor3300V
Because Vigor 3300 / 3300V user interface is very different from other Vigor models, we have created a top-level FAQ category for them. Fo now, click here. In future you will find all Vigor 3300...
View ArticleHow to configure IPSec VPN tunnels where the remote endpoint has ...
The Vigor 3300 models use the same list of profiles for LAN-to-LAN and host-to-LAN (teleworker) VPNs. There are however a subtle difference depending on whether the other endpoint has a static or...
View ArticleClik here to view.
How can I get the Console Log from a Vigor3300/V?
Connect a computer's serial port to the Vigor 3300 Console port using the supplied cable. this). On the computer, run a terminal emulator, such as the Windows Hyperterminal. Configure the serial...
View ArticleClik here to view.
Connecting DrayTek Broadband Routers to Optus Cable Service
This application note shows you how to configure the Optus supplied Netgear modem into bridge mode to interface Draytek broadband routers to Optus cable service. Applicable DrayTek routers DrayOS...
View Article
